Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
- 3. The two-litre engine (ADY)
   3.1. Removal and installation
   + 3.2. Dismantling and assemblage
   + 3.3. A head of the block of cylinders and valves
   + 3.4. Pistons and rods
   3.5. The block of cylinders
   + 3.6. A cranked shaft and radical bearings
   + 3.7. A mechanism drive газораспределения
   3.8. Tension adjustment приводного a belt of units of the engine
   3.9. An intermediate shaft
   3.10. Compression check in engine cylinders
   3.11. System of release of the fulfilled gases
   3.12. System of clearing with application of the activated coal
   3.13. System рециркуляции the fulfilled gases
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes
Folksvagen Sharan/Sharan repair>> The two-litre engine (ADY)>> System of release of the fulfilled gases
Fig. 160. A forward part of system of release ОГ on the 2,0-litre engine: 1 — a lining; 2 — a final collector; 3 — a bolt, 30 Н·м; 4 — a nut, 45 Н·м; 5 — a reception pipe; 6 — a nut: if M8 — 25 Н·м, if M10 — 40 Н·м; 7 — an arm; 8 — a bolt (as poses. 6)





The system of release of the fulfilled gases (ОГ) practically has the same design, as at engine VR6. The forward part of system of release ОГ (fig. 160) differs only.
Fig. 101. Elements of an average part of system of release of the fulfilled gases (are located between a reception pipe and the muffler of the catalyst): 1 — a nut of the screen of thermal protection; 2 — the screen of thermal protection; 3 — a direction to the first muffler; 4 — the catalyst; 5 — a protective collar; 6 — the screen of thermal protection; 7 — a bolt, 10 Н·м; 8 — a protective collar; 9 — a bolt, 10 Н·м; 10 — a nut, 40 Н·м; 11 — a ljambda-probe; 12 — штекерная колодка black colour




Fig. 102. Elements of a back part of system of release of the fulfilled gases: 1 — goes from the catalyst (the arrow 3 see fig. 101); 2 — a fastening collar; 3 — a nut, 40 Н·м; 4 — the suspension bracket ring, specifies in correct position at installation; 5 — a nut of the screen of thermal protection; 6 — the screen of thermal protection; 7 — the forward muffler; 8 — the back muffler; 9 — distance b = 50 mm; 10 — distance a = 5 mm




Average and back parts of system of release ОГ are similar or precisely same, as well as at engine VR6 (fig. 101 and 102 see).
All instructions resulted for engine VR6 (item 2.10.3 see) equally concern and the 2,0-litre engine, including sizes of intervals which are necessary for observing at installation of pipes.