Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
- 3. The two-litre engine (ADY)
   3.1. Removal and installation
   + 3.2. Dismantling and assemblage
   + 3.3. A head of the block of cylinders and valves
   + 3.4. Pistons and rods
   3.5. The block of cylinders
   + 3.6. A cranked shaft and radical bearings
   + 3.7. A mechanism drive газораспределения
   3.8. Tension adjustment приводного a belt of units of the engine
   3.9. An intermediate shaft
   3.10. Compression check in engine cylinders
   3.11. System of release of the fulfilled gases
   3.12. System of clearing with application of the activated coal
   3.13. System рециркуляции the fulfilled gases
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes


In case you're interested in knowing more info on exotic cars miami, stop by http://emcexoticrentals.com


Folksvagen Sharan/Sharan repair>> The two-litre engine (ADY)>> Tension adjustment приводного a belt of units of the engine
The tension поликлинового a belt is carried out by the mechanism with the built in spring and does not demand the regular control. Therefore it is not required to spend special adjustment of a tension of a belt if he for any reason has been removed.
Despite the fact that what various units can be established and for their reduction in action various pulleys can be used, in any case one tension roller is used only.

Fig. 156. The packing scheme поликлинового a belt on the car without the conditioner. To weaken a belt tension, turn the lever established on a tension roller in a direction, shown by an arrow




Fig. 157. The packing scheme поликлинового a belt on the car with the conditioner. To weaken a belt tension, turn the lever established on a tension roller in a direction, shown by an arrow




Packing schemes поликлинового a belt on the car without the conditioner and with the conditioner are presented on (fig. 156) and (fig. 157) accordingly.
Removal поликлинового a belt is carried out as follows:
- Mark a movement direction поликлинового a belt. For what draw a marker an arrow in a movement direction. The cranked shaft of the engine rotates clockwise if to take a detached view a belt;
- The lever 3299 (fig. 156 and 157 see) ослабьте a tension поликлинового a belt;
- Remove поликлиновой a belt with приводного the mechanism of the pump of the hydraulic booster of a steering;
- Remove поликлиновой a belt;
- Check up a condition поликлинового a belt. It should not have cracks or breaks, отслоений a covering or fibres, shabby fibres, обтрепавшихся or стекловидных lateral surfaces, oil or fat stains;
- Damaged поликлиновой it is necessary to replace a belt necessarily.
Installation поликлинового a belt is spent as follows:
- Turn the lever 3299 tension roller and put on поликлиновой a belt a tension roller and the generator (if it is established old поликлиновой a belt observe the direction of movement specified to it);
- Release the lever 3299 tension roller that поликлиновой the belt has stretched.