Repair VW Sharan. Diesel engines: 1,9 l TDI.+ 1. Introduction + 2. Engine VR6 + 3. The two-litre engine (ADY) + 4. System of greasing of the engine + 5. Cooling system + 6. System of injection of fuel of engine VR6 + 7. System Simos of injection of fuel of the 2,0-litre engine + 8. Ignition system + 9. Coupling + 10. A mechanical 5-step transmission + 11. Shaft of a drive of wheels + 12. The steering hydraulic booster + 13. A forward suspension bracket + 14. A back suspension bracket + 15. Brake system + 16. An electric equipment - 17. The diesel engine 17.1. Removal and installation + 17.2. Dismantling and assemblage + 17.3. A head of the block of cylinders + 17.4. Privodnye belts — поликлиновой and gear + 17.5. Shatunno - piston group + 17.6. An intermediate shaft 17.7. A flywheel - 17.8. A camshaft and a camshaft epiploon 17.8.1. Camshaft removal 17.8.2. Camshaft check 17.8.3. A camshaft epiploon 17.8.4. Installation of a camshaft and a camshaft epiploon in a head of the block of cylinders + 17.9. A cranked shaft and radical bearings + 17.10. The block of cylinders 17.11. Compression check in engine cylinders 17.12. System of release of the fulfilled gases + 18. System of greasing of the diesel engine + 19. System of cooling of the diesel engine + 20. The power supply system of the diesel engine and turbocharger + Maintenance service card + Specifications and characteristics + Electroschemes |
Folksvagen Sharan/Sharan repair>> The diesel engine>> Camshaft and camshaft epiploon>> Installation of a camshaft and camshaft epiploon in a head of the block of cylinders Well grease and insert pushers according to the marks put on them into apertures. If pushers have been removed, necessarily read instructions.
Plentifully oil a camshaft in the locations of bearings. Establish camshafts in their beds, and some times them turn. Establish shaft so that both cams of the first cylinder on two shaft looked upwards.
Being guided by fig. 435, put on covers of bearings № 1, 3 both 5 and a hand spread nuts. As bearing covers are displaced, check up, whether correctly they sit. For this purpose, being guided by drawing 406, define, whether correctly covers have been put on.
Tighten nuts of the established covers of bearings alternately and cross-wise for some passes by the moment of an inhaling 20 Н·м. Watch, that the surface of covers settled down opposite to a surface of a head of the block of cylinders.
Put on covers № 2 and № 4 and twirl nuts. Tighten nuts alternately and cross-wise in some passes by the moment of an inhaling 20 Н·м.
Take an epiploon of a camshaft and look, from what party the spring settles down. The party on which the spring settles down, should be directed inside. Grease a sealing surface (it is necessary to grease also a surface качения a camshaft). For installation of a new epiploon it is possible to use a pipe of suitable diameter. The pipe should correspond to the size of an external part of an epiploon completely.
Spread an epiploon directly and strike on it until its external surface will not come completely inside. To establish an epiploon it is possible also in the way shown on fig. 439.
Establish a camshaft cogwheel on a camshaft (do not forget about a wedge) and wrap a bolt with a washer. Keeping a camshaft in a motionless condition (for example, by means of old gear приводного a belt) also tighten a bolt the moment 80 Н·м.
Other works spend to sequences, return to removal process.
|
|