Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
- 17. The diesel engine
   17.1. Removal and installation
   + 17.2. Dismantling and assemblage
   + 17.3. A head of the block of cylinders
   + 17.4. Privodnye belts — поликлиновой and gear
   + 17.5. Shatunno - piston group
   + 17.6. An intermediate shaft
   17.7. A flywheel
   - 17.8. A camshaft and a camshaft epiploon
      17.8.1. Camshaft removal
      17.8.2. Camshaft check
      17.8.3. A camshaft epiploon
      17.8.4. Installation of a camshaft and a camshaft epiploon in a head of the block of cylinders
   + 17.9. A cranked shaft and radical bearings
   + 17.10. The block of cylinders
   17.11. Compression check in engine cylinders
   17.12. System of release of the fulfilled gases
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes




Folksvagen Sharan/Sharan repair>> The diesel engine>> Camshaft and camshaft epiploon>> Camshaft removal
For camshaft removal, on the established head of the block of cylinders remove at first a gear belt of drive ГРМ (item 17.4.1).
If it is required to remove a camshaft cogwheel it should be fixed in a motionless condition with the help оправки and to turn off a bolt. As the camshaft cogwheel sits tight on the place, insert into one of cogwheel apertures оправку and remove a wheel short blows of a rubber or plastic hammer. Remove segment шпонку a camshaft cogwheel. Otherwise remove a cogwheel of a camshaft after removal of the shaft.

Fig. 436. Covers of bearings of a camshaft have numbers put on them which go from left to right





The head of the block of cylinders with the camshaft located in it has an appearance now as on fig. 436. Remove a camshaft, being guided by a designation of numbers of covers of bearings.
Turn on slowly and alternately from each party of a cover of bearings № 1, 3 and 5 and remove them. Yet do not turn off a cover of bearings № 2 and № 4.
Ослабьте nuts of covers of bearings № 2 and № 4, everyone on 2 turns in regular intervals and cross-wise until both covers will not be turned off. Remove covers and take a camshaft. Number 1 can be in a cover a sealing ring for a cover of a head of the block of cylinders.
Clamp a shaft in a vice with metal cheeks and turn away a bolt of a cogwheel of a camshaft if it is not made yet. Remove a cogwheel and take an elastic washer. Remove an epiploon on the other hand.
Take out pushers if it is necessary. That them not to mix, mark them, having put on them from the inside risks: for the first pusher — one, for second two etc. Readout is conducted from outside where the drive газораспределительного the mechanism is located.
Combine pushers from outside a camshaft on a pure matter that oil has not flowed out.