Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
- 15. Brake system
   + 15.1. Adjustment of brake system
   + 15.2. Disk brakes of forward wheels
   + 15.3. Brakes of back wheels
   15.4. Processing of brake disks
   + 15.5. The main brake cylinder
   15.6. Check of the vacuum amplifier of a brake drive
   15.7. Prorolling of brakes
   - 15.8. A lay brake
      15.8.1. Removal and installation of a cable of a drive of a lay brake
      15.8.2. Removal and installation of the lever of a drive of a lay brake
   + 15.9. System ABS (antiblocking brake system)
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes
Folksvagen Sharan/Sharan repair>> Brake system>> Lay brake>> Removal and installation of a cable of a drive of a lay brake
Removal тросовой draughts of the lever of a drive of a lay brake spend in a following order:
- ослабьте bolts of fastening of back wheels, put a back part of the car on a support and remove wheels;
- Establish the lever of a drive of a lay brake in extreme bottom position;
Fig. 330. Details of lay brake system: 1 — the handle; 2 — a casing of the lever of a lay brake; 3 — a lever frame; 4 — a bolt, 25 Н·м; 5 — шарнирный a bolt; 6 — the lever of a drive of a lay brake; 7 — the contact switch; 8 — a protective cover тросовой draughts of the lever of a lay brake; 9 — шплинт; 10 — тросовая draught of the lever of a lay brake; 11 — the equalizer; 12 — an adjusting nut; 13 — spring fastening; 14 — a returnable spring; 15 — a fastening loop.





- Turn on an adjusting nut 12 (fig. 330) a cable 10 drives of a lay brake until рычажки a manual drive on back brake supports will not depart to the emphasis;
- Remove ослабшие cables of a drive of a lay brake from the equalizer 11 and with скоб fastenings;
Fig. 331. Places of fastening of cables of a drive of a lay brake on a back suspension bracket (are shown by arrows)





- Disconnect from fastenings on a back suspension bracket (fig. 331) cables of a drive of a lay brake;
- Disconnect cables of a drive of a lay brake from рычажков a manual drive on back brake supports. For this purpose take out a lock collar, pull a cable against a tension of a spring and unhook the end of a cable from рычажка;
- Take out a cable through a back suspension bracket.
Check up a condition of details of lay brake system. If are found out breakage, перетирание проволок a cable, bad fastening of tips on it or cover damage, a cable replace new. Sector and latch teeths should not have damages. And the lever should be fixed reliably in the set position and it is easy to move upwards-downwards. The damaged and worn out details replace.
Installation тросовой draughts of the lever of a drive of a lay brake spend in an order, the return to removal. After installation adjust a lay brake and tighten bolts of fastening of back wheels the moment 140 Н·м.