Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
- 4. System of greasing of the engine
   4.1. Removal and pallet installation картера
   + 4.2. The oil pump
   4.3. The oil filter
   4.4. Check of pressure of oil
   4.5. An oil radiator
   4.6. Oil replacement in the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes




Folksvagen Sharan/Sharan repair>> System of greasing of the engine>> Removal and pallet installation картера
The pallet картера can be removed from the engine established on the car. Pallet removal картера is spent in a following order:

Fig. 166. System of greasing of the 2,0-litre engine: 1 — a lining, replace with the new; 2 — a cover маслоналивной mouths; 3 — щуп for check of level of oil; 4 — a directing tube щупа for check of level of oil; 5 — the switch of pressure of oil on 25 кПа; 6 — the switch of pressure of oil on 180 кПа; 7 — the return valve, 5 Нм; 8 — заглушки; 9 — a nut, 25 Нм; 10 — the basis of the oil filter; 11 — an O-shaped sealing ring, always on replacement; 12 — an oil radiator; 13 — the oil filter; 14 — a gear wheel of the oil pump; 15 — a cover of the oil pump with редукционным the valve; 16 — a bolt, 10 Нм; 17 — a bolt, 20 Нм; 18 — a bolt of fastening oil картера; 19 — a sealing ring, replace; 20 — a stopper of an aperture for oil plum; 21 — the oil pallet; 22 — a lining, replace with the new; 23 — маслоприемник; 24 — an oil directing guard; 25 — a lining, replace with the new





- Turn away a stopper 20 (fig. 166) apertures for plum of oil see and completely merge from the engine engine oil in in advance prepared capacity;

The note
To utilise old engine oil follows according to rules of preservation of the environment.

- Remove protection картера the engine;
- Turn away bolts of 18 fastenings and remove the pallet картера 21 together with a lining 22.

The note
On the 2,0-litre engine it is heavy to reach bolts of fastening of the oil pallet, located from outside a flywheel. On HUNDRED special keys for bolts 3249 and 3185 are for this purpose used.

Pallet installation картера spend to sequences, return to removal, thus observe following moments:
- Old lining of the pallet always replace with the new. Watch, that the lining has not moved at installation;
- Before installation put on surfaces of contact of the oil pallet and the block of cylinders hermetic D2;
- In regular intervals cross-wise tighten bolts of fastening of the pallet картера. Bolts with шестигранной a head are tightened by the moment 20 Нм (the engine 2,0) or the moment 15 Нм (engine VR6);
- Fill in in the engine of engine oil of 5,5 l if the oil filter acted in film;
- If the oil filter did not act in film, fill in 5,0 l of oil.