Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
- 4. System of greasing of the engine
   4.1. Removal and pallet installation картера
   + 4.2. The oil pump
   4.3. The oil filter
   4.4. Check of pressure of oil
   4.5. An oil radiator
   4.6. Oil replacement in the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes




Folksvagen Sharan/Sharan repair>> System of greasing of the engine>> Oil radiator
At work of the engine the temperature картерного oils should not raise strongly in order to avoid falling of its viscosity. Partial cooling of oil occurs in the pallet картера and in the case of the filter owing to обдува their air from the fan of system of cooling. картерного oils apply oil radiators to more intensive cooling.
Because of the different device of oil filters on engines VR6 and 2,0 l are used various oil radiators.
The engine of 2,0 l

Fig. 177. Details of the oil pump of the 2,0-litre engine: 1 — a bolt, 25 Нм; 2 — the basis of the oil filter; 3 — a sealing ring; 4 — an oil radiator; 5 — a nut, 25 Нм; 6 — the oil filter





On the 2,0-litre engine an oil radiator 4 (fig. 177) is located between the basis 2 oil filters and the oil filter 6. The oil radiator acts in film only after removal of the oil filter and a detachment of hoses. For this purpose turn away a nut 5 from the bottom surface of an oil radiator. Between an oil radiator and the basis the sealing ring 3 is established. At assemblage the nut should be tightened the moment 25 Нм.
Engine VR6

Fig. 178. An arrangement of an oil radiator on a lateral face of the block of cylinders of engine VR6: 1 — a directing tube щупа for check of level of oil; 2 — an O-shaped sealing ring; 3 — a cover, 25 Нм; 4 — an oil radiator; 5 — an O-shaped sealing ring





On engine VR6 the oil radiator of liquid cooling is established on a lateral face of the block of cylinders (fig. 178).
At liquid cooling the oil radiator consists in the case through which there passes a working liquid of system of cooling of the engine, and decrease in temperature of engine oil is carried out by a cooling liquid. Hoses for a supply and tap of a cooling liquid approach to joining places on the filter.
To remove the oil filter it is possible after the cooling liquid from system of cooling will be merged and hoses of a supply of a cooling liquid are disconnected. Then turn away a cover from an outer side of the oil filter and remove a radiator. On each party of an oil radiator there is an O-shaped sealing ring which should be changed always if the oil radiator has been removed.
The oil radiator with liquid cooling provides not only oil cooling at work under trying conditions, but also fast warming up of oil at engine start-up.
At installation of an oil radiator grease both sealing rings with engine oil. Establish a radiator and tighten a cover the moment 25 Нм. Attach hoses and fill in cooling liquid in cooling system.