Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
- 16. An electric equipment
   + 16.1. The storage battery
   + 16.2. The generator
   - 16.3. A starter
      16.3.1. Starter check
      16.3.2. Removal and starter installation
      16.3.3. Dismantling and starter assemblage
   + 16.4. Screen wipers
   + 16.5. Headlights
   16.6. Back lanterns
   16.7. Replacement of lamps of forward indexes of turn
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes




Folksvagen Sharan/Sharan repair>> Electric equipment>> Starter>> Removal and starter installation
Starter removal spend in a following order:
- Disconnect "a mass" wire from conclusion АБ (do not forget about a protective code of a radio tape recorder);
- Raise a forward part of the car and establish it on support;
- Remove a noise isolation from below a motor compartment;
The work course has differences for the 2,0-litre engine and for engine VR6:
The 2,0-litre engine

Fig. 337. The black plastic cover and a socket of the involving relay (the 2,0-litre engine) are shown by arrows





Before to disconnect wires from a starter, remove a black plastic cover and disconnect an electric socket of the involving relay being under it (fig. 337);

Fig. 338. The arrangement of plugs 30 and 50 on the involving relay is shown by arrows





- Disconnect a socket (the plug 50) from the involving relay and turn away a nut of the plug 30 (fig. 338) and unbend a wire aside;

Fig. 339. Under a nut (it is shown by an arrow) the fastening nut is located





- Turn away a nut and bolts of fastening of a starter. The nut (fig. 339) is wound on an adjusting pin;
- Remove a starter.
Starter installation spend in an order, the return to removal, carrying out the following:

Fig. 340. At starter installation tighten the nut shown by an arrow the moment 45 Нм





- Tighten a nut (fig. 340) fastenings of a starter by the moment 45 Нм;
- Pay attention to correctness of joining of wires;
- Tighten a nut (fig. 339) (located over already tightened by moment 45 Нм a nut see) the moment 10 Нм;
- Tighten a nut of the plug 30 moment 10 Нм;
- Connect АБ and enter a protective code of a radio tape recorder and at once check up starter work.
Removal and installation of a starter from the car with engine VR6
On car Sharan with engine VR6 removal and starter installation is carried out in the way described above, however that fastening of a starter there are following features a little:

Fig. 341. At starter installation (engine VR6 from a manual transmission) a nut 1 and a bolt 2 are tightened by the moment 45 Нм





- The starter fastens on engine VR6 from a manual transmission by means of a bolt 2 (fig. 341) and nuts 1 (at installation they are tightened by the moment 45 Нм);

Fig. 342. At starter installation (engine VR6 from an automatic transmission) the nut on an adjusting pin is tightened by the moment 60 Нм





- On engine VR6 with an automatic transmission the starter fastens nuts on adjusting pins. At installation of a starter the nut (fig. 342, it is shown by an arrow) is tightened by the moment 60 Нм;

Fig. 343. At starter installation (engine VR6 from an automatic transmission) the bottom nut is tightened by the moment 60 Нм





- Tighten the bottom nut (fig. 343, it is shown by an arrow) starter fastenings to engine VR6 from an automatic transmission the moment 60 Нм;

Fig. 344. The nut of fastening of the holder of a wire is tightened by the moment 10 Нм





- Tighten a nut (the marksman, fig. 344), крепящую the holder of a wire the moment 10 Нм, and a nut of the plug 30 moment 10 Нм.