Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
+ 13. A forward suspension bracket
- 14. A back suspension bracket
   14.1. Removal and installation
   14.2. The longitudinal lever of a suspension bracket / of a spring of a suspension bracket — removal and installation
   14.3. Removal and installation of shock-absorbers
   14.4. Bearings of back wheels
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes
Folksvagen Sharan/Sharan repair>> Back suspension bracket>> The longitudinal lever of a suspension bracket / of a spring of a suspension bracket — removal and installation
At removal of the longitudinal lever the screw spring acts in film also:
- Put a back part of the car on support and remove back wheels;
Fig. 305. The Bottom view of the levelling lever of a lay brake. After counternut easing (it is shown by an arrow) it is possible to weaken a tension of a cable of a lay brake





- ослабьте a counternut (fig. 305) on the bottom of the car also turn away an adjusting nut so that the equalizer keeping cables of a lay brake, has departed, and cables ослабли;
- Remove the gauge of frequency of rotation АBS (section 15 «Brake system» see).
- Disconnect cables of a drive of a lay brake from скоб the brake mechanism. Remove for this purpose a spring collar and unhook the end of a cable from the lever;
- Separate connections of pipelines of a brake drive and brake hoses (see подразд. 14.1);
Fig. 299. Two bolts крепят скобу the disk brake mechanism (a support of the disk brake mechanism) to a beam of a nave of a wheel





- Remove скобу the brake mechanism (fig. 299 see);
Fig. 306. Fastening of a brake disk: 1 — a bolt; 2 — a disk





- Remove a brake disk (fig. 306). Carefully clear working surfaces of a brake disk and a wheel nave;
Fig. 301. Fastening of a back suspension bracket: 1 — a basic plate; 2 — the car bottom





- Remove the stabilizer of cross-section stability (fig. 301 see);
- Substitute under the longitudinal lever a jack, raise it so that the shock-absorber was a little compressed, and remove the bottom fastening of the shock-absorber;
- Lower a jack and take out a back spring (operation is carried out together);
Fig. 304. Fastening of the cross-section lever of a back suspension bracket and the stabilizer of cross-section stability: 1 — скоба fastenings of the stabilizer of cross-section stability; 2 — a bolt, 30 Н·м; 3 — the cross-section lever of a back suspension bracket; 4 — a bolt, 30 Н·м; 5 — the stabilizer of cross-section stability; 6 — a rubber support; 7 — a rubber support; 8 — a collar of the stabilizer of cross-section stability; 9 — a suspension bracket support; 10 — bolts, 65 Н·м; 11 — a bolt, 260 Н·м; 12 — a cross-beam; 13 — a nut, 170 Н·м; 14 — резинометаллическая a support





- Remove the longitudinal lever from the interior of (fastening places are shown on fig. 304).
Installation of the longitudinal lever is carried out in sequence, return to removal process.






QX4.ONLINE
S40.ONLINE
A-8.ONLINE
W124.ONLINE
RX300.ONLINE
W140.ONLINE
B3-B4.SPACE
B3B4.SPACE
A-8.SPACE