Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
- 13. A forward suspension bracket
   13.1. Removal and installation
   - 13.2. Repair of a forward suspension bracket
      13.2.1. A screw spring and the shock-absorber
      13.2.2. Replacement of bearings of wheels
      13.2.3. Removal and installation of cross-section levers
   13.3. The stabilizer of cross-section stability
   + 13.4. Adjustment of corners of installation of forward wheels
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes
Folksvagen Sharan/Sharan repair>> Forward suspension bracket>> Repair of a forward suspension bracket>> Removal and installation of cross-section levers
Fig. 291. Fastening of the cross-section lever, the stabilizer of cross-section stability and a pendular support on a stretcher: 1 — a stretcher; 2 — a nut, 55 Н·м; 3 — a rubber support; 4 — самоконтрящаяся a nut, 100 Н·м (replace always); 5 — fixing скоба; 6 — a bolt; 7 — connecting draught; 8 — the stabilizer of cross-section stability; 9 — самоконтрящаяся a nut, 100 Н·м (replace always); 10 — bolt M14x1,5, length 65 mm, 150 Н·м + 90 °; 11 — the back bearing of the cross-section lever; 12 — bolt M14x1,5, length 95 mm, 150 Н·м + 90 ° (replace always); 13 — a spherical support; 14 — a bolt, 55 Н·м; 15 — самоконтрящаяся a nut, 55 Н·м (replace always); 16 — the cross-section lever; 17 — the bearing of the cross-section lever; 18 — a bolt, 90 Н·м + 90 °; 19 — a bolt, 100 Н·м; 20 — a rubber support; 21 — a pendular support; 22 — a nut, 100 Н·м; 23 — a bolt




In drawing 291 elements of a forward suspension bracket are shown. An order of dismantle of cross-section levers of a forward suspension bracket:
- Establish a forward part of the car on support and remove a forward wheel;
- Remove engine protection;
Fig. 284. Two bolts (are shown by an arrow) keep the bottom part of a spherical support in the bottom part of a rotary fist




Fig. 292. Before removal of a finger of a spherical support (fig. 285 see), remove a nut 1 till the end of a carving




Fig. 285. Take a finger of a spherical support from the cross-section lever by means of a stripper




- Turn away a nut (fig. 292). If you change only a spherical support turn away bolts (see fig. 284) and remove a spherical support from the cross-section lever (fig. 285 see);
- Turn away bolts of fastening of the cross-section lever on an inside of a stretcher and remove the cross-section lever. Plugs of the cross-section lever take by means of approaching оправки.
Installation is carried out in return sequence concerning removal process, thus:
- Use new bolts of fastening of the cross-section lever. As the cross-section lever fastens by means of резинометаллических plugs tighten its bolts only when the car costs wheels on a ground;
- Tighten bolts of fastening of a spherical support the moment 55 Н·м;
- If you took a finger of a spherical support from a rotary fist again establish it against the stop and screw a new nut. The moment of an inhaling of a nut 30 Н·м, and then tighten it for 90 °. If the finger of a spherical support rotates, establish in it шестигранник 7 mm and tighten a nut.