Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. The steering hydraulic booster
- 13. A forward suspension bracket
   13.1. Removal and installation
   + 13.2. Repair of a forward suspension bracket
   13.3. The stabilizer of cross-section stability
   + 13.4. Adjustment of corners of installation of forward wheels
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes




Folksvagen Sharan/Sharan repair>> Forward suspension bracket>> The stabilizer of cross-section stability
The way of fastening of the stabilizer of cross-section stability is shown in drawing 291. To get access to the stabilizer of cross-section stability remove a stretcher and a pendular support:
- Establish a forward part of the car on support;
- Remove engine protection;
- From outside salon separate connection of a steering column and the steering mechanism (item 12.1 see);
- Remove connecting draught of the stabilizer of cross-section stability;

Fig. 293. Fastening of 1 stabilizer of cross-section stability to a stretcher





- Remove fastening of 1 stabilizer of cross-section stability from a stretcher (fig. 293);
- Establish a jack under a stretcher;

Fig. 294. Removal of a pendular support from a transmission: 1 — a bolt; 2 — a washer; 3 rubber support; 4 — a pendular support





- Remove a pendular support of a transmission (fig. 294). Turn away a bolt 1 and remove it together with a washer 2. Remove a rubber support 3 and wring out a pendular support 4;

Fig. 295. On each party of the car are located on two bolts of fastening of a stretcher (are shown by arrows)





- Turn away four bolts of fastening of a stretcher. Turn away two bolts (fig. 295) from each party of the car;
- Slowly lower a stretcher and remove the stabilizer of cross-section stability.
Installation is carried out in return sequence concerning removal process, thus:
- Do not damage a sheeting of the stabilizer of cross-section stability;
- Do not damage protective covers of hinges;

Fig. 291. Fastening of the cross-section lever, the stabilizer of cross-section stability and a pendular support on a stretcher: 1 — a stretcher; 2 — a nut, 55 Нм; 3 — a rubber support; 4 — самоконтрящаяся a nut, 100 Нм (replace always); 5 — fixing скоба; 6 — a bolt; 7 — connecting draught; 8 — the stabilizer of cross-section stability; 9 — самоконтрящаяся a nut, 100 Нм (replace always); 10 — bolt M14x1,5, length 65 mm, 150 Нм + 90 ; 11 — the back bearing of the cross-section lever; 12 — bolt M14x1,5, length 95 mm, 150 Нм + 90 (replace always); 13 — a spherical support; 14 — a bolt, 55 Нм; 15 — самоконтрящаяся a nut, 55 Нм (replace always); 16 — the cross-section lever; 17 — the bearing of the cross-section lever; 18 — a bolt, 90 Нм + 90 ; 19 — a bolt, 100 Нм; 20 — a rubber support; 21 — a pendular support; 22 — a nut, 100 Нм; 23 — a bolt





- Replace 291 bolts specified in fig. and nuts;
- The moments of an inhaling of carving connections are specified in the end of the book.