Repair VW Sharan

. Diesel engines: 1,9 l TDI.
+ 1. Introduction
+ 2. Engine VR6
+ 3. The two-litre engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of engine VR6
+ 7. System Simos of injection of fuel of the 2,0-litre engine
+ 8. Ignition system
+ 9. Coupling
+ 10. A mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
- 12. The steering hydraulic booster
   + 12.1. A steering drive
   + 12.2. Replacement of cross-section steering draughts
   - 12.3. Hydraulic system
      12.3.1. Filling of hydraulic system and removal from it air
      12.3.2. Check of hydraulic system on tightness
      12.3.3. Tension adjustment клинового a belt of the pump of the hydraulic booster of a steering
      12.3.4. Removal and installation of the pump of the hydraulic booster of a steering
   12.4. Hoses, pipelines
+ 13. A forward suspension bracket
+ 14. A back suspension bracket
+ 15. Brake system
+ 16. An electric equipment
+ 17. The diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. The power supply system of the diesel engine and turbocharger
+ Maintenance service card
+ Specifications and characteristics
+ Electroschemes
Folksvagen Sharan/Sharan repair>> The steering hydraulic booster>> Hydraulic system>> Tension adjustment клинового a belt of the pump of the hydraulic booster of a steering
Fig. 270. Tension adjustment приводного a belt of the pump of the hydraulic booster on the four-cylinder engine: 1 and 4 — nuts; 2 — a bolt; 3 — a lock bolt; A — the special tool (1410 and 1410/2)





If to press a finger in the belt centre приводной the belt should be pressed through approximately on 5 mm. For adjustment of a tension of a belt of the four-cylinder engine the special tool — a nozzle on динамометрический a key (fig. 270) is used. In the absence of the special tool, use a face head (22 mm) with динамометрическим a key.
Establish a forward part of the car on support:
- ослабьте nuts 1 and 4 (fig. 270 see);
Fig. 271. An arm of the pump of the hydraulic booster of a steering: 1 — a bolt, 25 Н·м; 2 — a bolt, 25 Н·м; 3 — a bolt, 25 Н·м; 4 — скоба pump suspension brackets; 5 — a suspension bracket arm; 6 — a bolt, 25 Н·м; 7 — adjusting скоба; 8 — an adjusting bolt; 9 — a pin (only on the petrol engine)





- ослабьте a lock bolt 3 adjusting bolts of a tension приводного a belt (on fig. 271 at number 8);
- Tighten a nut 3 moment of an inhaling 4 Н·м, if a belt not the new. For new клинового a belt the inhaling moment should make 7 Н·м. Keeping a nut in this position, tighten a lock bolt the moment 25 Н·м;

The note
If at you is not present динамометрического a key tighten a nut so that the belt was pressed through approximately on 5 mm. Keeping a nut in this position, tighten a lock bolt.

- Tighten a bolt 1 moment 45 Н·м, bolts 2 and 4 moment 25 Н·м;
- Make a trial trip on the car and check up a tension клинового a belt once again.