Repair VW Sharan. Diesel engines: 1,9 l TDI.+ 1. Introduction + 2. Engine VR6 + 3. The two-litre engine (ADY) + 4. System of greasing of the engine + 5. Cooling system + 6. System of injection of fuel of engine VR6 + 7. System Simos of injection of fuel of the 2,0-litre engine + 8. Ignition system + 9. Coupling + 10. A mechanical 5-step transmission - 11. Shaft of a drive of wheels - 11.1. Removal and power shaft installation 11.1.1. On the car with a mechanical transmission 11.1.2. On the car with an automatic transmission 11.2. Power shaft repair + 12. The steering hydraulic booster + 13. A forward suspension bracket + 14. A back suspension bracket + 15. Brake system + 16. An electric equipment + 17. The diesel engine + 18. System of greasing of the diesel engine + 19. System of cooling of the diesel engine + 20. The power supply system of the diesel engine and turbocharger + Maintenance service card + Specifications and characteristics + Electroschemes |
Folksvagen Sharan/Sharan repair>> Shaft of a drive of wheels>> Removal and power shaft installation>> On the car with an automatic transmission Removal is made similarly described: after the rotary fist will be outside unbent, turn away bolts of a flange of a shaft on a transmission.
Removal of the right power shaft
Follow the resulted instructions until the shaft end will not be taken from the wheel bearing (fig. 260 see);
- Turn away both bolts of the average bearing (fig. 247 see) and completely take out a power shaft from a transmission.
After removal of a power shaft the car cannot be moved, otherwise it is possible to damage the wheel bearing. If the car nevertheless is required to be moved, establish an old SHRUS instead of a shaft and tighten a bolt of its fastening by the moment 50 Н·м.
Power shaft installation is carried out in sequence, return to removal process, thus:
- Replace a lock ring on the power shaft end.
Installation of the left power shaft
On the car with an automatic transmission insert the internal hinge of the left power shaft in шлиц differential gear wheels (fig. 261).
With plastic or rubber hammer hammer the internal hinge against the stop. Do not damage thus a sealing ring. To establish the left power shaft, make the following:
- Carefully clear шлицы a power shaft and an inside of a nave of a wheel of greasing;
- Insert the external end of a power shaft into the wheel bearing in sequences, return shown on fig. 260;
- Wrap a new bolt with a fillet and a washer in the end of a power shaft and tighten the moment not less than 50 Н·м;
- Establish all removed parts of a forward suspension bracket of a wheel. The moments of an inhaling of connections are specified in the end of the book;
- Establish a wheel, lower the car on wheels and tighten a nut the moment 150 Н·м, and from final position, already without динамометрического a key, turn it on a turn quarter (90 °). Tighten bolts of fastening of a wheel the moment 140 Н·м;
- Check up level трансмиссионного oils and if necessary add it.
Installation of the right power shaft
Insert a power shaft into a transmission. Do not damage thus the sealing ring located in картере of a transmission;
- Establish the intermediate bearing of a power shaft to the block of cylinders (fig. 247 see);
- Insert the external end of a power shaft in шлиц the bearing of a wheel and establish a new bolt with a washer;
- Other operations are spent similarly to installation of the left power shaft.
On the car with an automatic transmission
Attach the internal hinge of a power shaft to a flange of a shaft of a transmission. Tighten bolts the moment 80 Н·м;
- Hammer the internal hinge of a shaft against the stop and tighten bolts of the intermediate bearing;
- Insert the external hinge of a shaft in шлиц the bearing of a wheel and wrap a new bolt with a fillet and a washer and the moment 50 Н·м;
- Other works are spent similarly to installation of the left power shaft.
|
|